We usually did this, but sometimes they were named after what they did,
rather than what they cleaned up.
There are still a few exceptions:
1. I didn't bother creating destroy_xxx wrappers for htable routines
which already existed.
2. Sometimes destructors really are used for side-effects (eg. to simply
mark that something was freed): these are clearer with boutique names.
3. Generally destructors are static, but they don't need to be: in some
cases we attach a destructor then remove it later, or only attach
to *some* cases. These are best with qualifiers in the destroy_<type>
name.
Suggested-by: @ZmnSCPxj
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This provides a sanity check that we are in sync, and also keeps the
logic in the program and out of the SQL.
Since the destructor now doesn't clean up the peer, there are some
wider changes to be made when cleaning up. Most notably we create
lots of channels in run-wallet.c and they previously freed the peer:
now we need free the peer explicitly, so we need to free them first.
Suggested-by: @cdecker
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
And return the correct error message for the channel they give, if
they try to re-establish on an error channel.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Channels are within the peer structure, but the peer is freed only
when the last channel is freed.
We also implement channel_set_owner() and make peer_set_owner() a temporary
wrapper.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Much like the database; peer contains id, address, channel contains
per-channel information. Where we create a channel, we always create
the peer too.
For the moment, peer->log and channel->log coexist side-by-side, to
reduce some of the churn.
Note that this changes the API to dev-forget-channel: if we have more
than one channel, we insist they specify the short-channel-id.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This is not connected yet; during the transition, there will be a 1:1
mapping from channel to peer, so we can use channel2peer and peer2channel
to shim between them.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Both when we forget about an opening peer, and at startup. We're
going to be relying on this, and the next patch, as we refactor
peer/channel handling to mirror the db.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Combining the two was just awkward, so it's clearer to have separate
functions. And we make the lower-level functions do the escaping.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The JSON-RPC spec specifies that if the request is unparseable we
should return an error with a NULL id. This is a bit more friendly
than slamming the door in the face.
Signed-off-by: Christian Decker <decker.christian@gmail.com>
As reported by @practicalswift in #945 it is possible to inject
non-printable, or shell escape, characters in a json command, that
will fail to parse and then clear the shell.
Reported-by: @practicalswift
Signed-off-by: Christian Decker <decker.christian@gmail.com>
Now we have wirestring, this is much more natural. And with the
24M length limit, we needn't be so concerned about dumping 64k peer
messages in hex.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
These are now logically arrays of pointers. This is much more natural,
and gets rid of the horrible utxo array converters.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
`activate_peer` does little more than wiring up some txwatches and
asking `gossipd` to reconnect to the peer. If the peer manages to
reconnect before we activate then we would crash.
This just changes the `assert` causing the crash into a conditional
whether we need to reconnect or not.
Signed-off-by: Christian Decker <decker.christian@gmail.com>
Due to the broadcast failure quite a few users are reporting channels
stuck in awaiting lockin. This commit adds a `dev-forget-channel`
command that checks whether the funding outpoint is in the UTXO, and
forgets the channel if not. The UTXO check can be overridden with the
`force` parameter, but that is dangerous.
Signed-off-by: Christian Decker <decker.christian@gmail.com>
We were sideloading it, which is awkward, now it's a field that we can
actually use in the code.
Signed-off-by: Christian Decker <decker.christian@gmail.com>
We currently don't handle LOG_IO properly, and we turn it into a string
before handing it to the ->print function, which makes it ugly for
the case where we're using copy_to_parent_log, and also means in
that case we lose *what peer* the IO is coming from.
Now, we handle the io as a separate arg, which is much neater.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Logging often gets called in error paths, so this is just good hygiene.
Also, log_io does this already.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Rusty Russell
Christian Decker
root
ZmnSCPxj
practicalswift