We're getting spurious closures, even on mainnet. Using --ignore-fee-limits
is dangerous; it's slightly less so to lower the minimum (which is the
usual cause of problems).
So let's halve it, but beware the floor.
This is a workaround, until we get independent feerates in the spec.
Fixes: #613
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Currently we intuit it from the fd being closed, but that may happen out
of order with when the master thinks it's dead.
So now if the gossip fd closes we just ignore it, and we'll get a
notification from the master when the peer is disconnected.
The notification is slightly ugly in that we have to disable it for
a channel when we manually hand the channel back to gossipd.
Note: as stands, this is racy with reconnects. See the next patch.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
(This was sitting in my gossip-enchancement patch queue, but it simplifies
this set too, so I moved it here).
In 94711969f we added an explicit gossip_index so when gossipd gets
peers back from other daemons, it knows what gossip it has sent (since
gossipd can send gossip after the other daemon is already complete).
This solution is insufficient for the more general case where gossipd
wants to send other messages reliably, so replace it with the other
solution: have gossipd drain the "gossip fd" which the daemon returns.
This turns out to be quite simple, and is probably how I should have
done it originally :(
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
1. Lifetime of 'struct reaching' now only while we're actively doing connect.
2. Always free after a single attempt: if it's an important peer, retry
on a timer.
3. Have a single response message to master, rather than relying on
peer_connected on success and other msgs on failure.
4. If we are actively connecting and we get another command for the same
id, just increment the counter
The result is much simpler in the master daemon, and much nicer for
reconnection: if they say to connect they get an immediate response,
rather than waiting for 10 retries. Even if it's an important peer,
it fires off another reconnect attempt, unless it's actively
connecting now.
This removes exponential backoff: that's restored in next patch. It
also doesn't handle multiple addresses for a single peer.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
And on channel_fail_permanent and closing (the two places we drop to
chain), we tell gossipd it's no longer important.
Fixes: #1316
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This will allow us in the next commit to store the transactions that triggered
this event in the DB and thus allowing us to replay them later on.
Signed-off-by: Christian Decker <decker.christian@gmail.com>
d822ba1ee accidentally removed this case, which is important: if the
other side didn't get our final matching closing_signed, it will
reconnect and try again. We consider the channel no longer "active"
and thus ignore it, and get upset when it send the
`channel_reestablish` message.
We could just consider CLOSINGD_COMPLETE to be active, but then we'd
have to wait for the closing transaction to be mined before we'd allow
another connection.
We can't special case it when the peer reconnects, because there
could be (in theory) multiple channels for that peer in CLOSINGD_COMPLETE,
and we don't know which one to reestablish.
So, we need to catch this when they send the reestablish, and hand
that msg to closingd to do negotiation again. We already have code
to note that we're in CLOSINGD_COMPLETE and thus ignore any result
it gives us.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The new connect code revealed an existing race: we tell gossipd to
release the peer, but at the same time it connects in. gossipd fails
the release because the peer is remote, and json_fundchannel fails.
Instead, we catch this race when we get peer_connected() and we were
trying to open a channel. It means keeping a list of fundchannels which
are awaiting a gossipd response though.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We missed it in some corner cases where we crashed/were killed between
being told of the lockin and sending the channel_normal_operation message.
When we were restarted, we were told both sides were locked in already,
so we never updated the state.
Pull the entire "tell channeld" logic into channel_control.c, and make
it clear that we need to keep waching if we cant't tell channeld. I think
we did get this correct in practice, since funding_announce_cb has the
same test, but it's better to be clear.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Also report tx and txid, and whether we closed unilaterally or
bilaterally, if we could close the channel.
Also make a manpage.
Fixes: #1207Fixes: #714Fixes: #622
All of the callback functions were only using the tx to generate the txid again,
so we just pass that in directly and save passing the tx itself.
This is a simplification to move to the DB backed depth callbacks. It'd be
rather wasteful to read the rawtx and deserialize just to serialize right away
again to find the txid, when we already searched the DB for exactly that txid.
Signed-off-by: Christian Decker <decker.christian@gmail.com>
I didn't convert all tests: they can still use a standalone context.
It's just marginally more efficient to share the libwally one for all
our daemons which link against it anyway.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This bug is a classic case of being lazy:
1. peer_accept_channel() allocated its return off the input message,
rather than taking an explicit allocation context. This concealed the
lifetime nature of the return.
2. The context for sanitize_error was the error itself, rather than the
more obvious tmpctx (connect_failed does not take).
The global tmpctx removes the "efficiency" excuse for grabbing a random
object to use as context, and is also nice and explicit.
All-the-hard-work-by: @ZmnSCPxj
As we add more features, the current code is insufficient.
1. Keep an array of single feature bits, for easy switching on and off.
2. Create feature_offered() which checks for both compulsory and optional
variants.
3. Invert requires_unsupported_features() and unsupported_features()
which tend to be double-negative, all_supported_features() and
features_supported().
4. Move single feature definition from wire/peer_wire.h to common/features.h.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This simplifies things, and means it's always in the database. Our
previous approach to creating it on the fly had holes when it was
created for onchaind, causing us to use another every time we
restarted.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Will be used later to filter out outputs we are interested in, and
trigger db updates with them.
Signed-off-by: Christian Decker <decker.christian@gmail.com>
We always hand in "NULL" (which means use tal_len on the msg), except
for two places which do that manually for no good reason.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
ZmnSCPxj
Rusty Russell
practicalswift
Christian Decker
John Barboza
Igor Cota