You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
75 lines
3.0 KiB
75 lines
3.0 KiB
# Licensed to the Apache Software Foundation (ASF) under one
|
|
# or more contributor license agreements. See the NOTICE file
|
|
# distributed with this work for additional information
|
|
# regarding copyright ownership. The ASF licenses this file
|
|
# to you under the Apache License, Version 2.0 (the
|
|
# "License"); you may not use this file except in compliance
|
|
# with the License. You may obtain a copy of the License at
|
|
#
|
|
# http://www.apache.org/licenses/LICENSE-2.0
|
|
#
|
|
# Unless required by applicable law or agreed to in writing,
|
|
# software distributed under the License is distributed on an
|
|
# "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY
|
|
# KIND, either express or implied. See the License for the
|
|
# specific language governing permissions and limitations
|
|
# under the License.
|
|
#
|
|
|
|
syscfg.defs:
|
|
BLE_PHY_SYSVIEW:
|
|
description: >
|
|
Enable SystemView tracing module for radio driver.
|
|
value: 0
|
|
|
|
BLE_PHY_CODED_RX_IFS_EXTRA_MARGIN:
|
|
description: >
|
|
This defines additional margin for T_IFS tolerance while in
|
|
RX on coded phy to allow maintaining connections with some
|
|
controllers that exceed proper T_IFS (150 usecs) by more
|
|
than allowed 2 usecs.
|
|
This value shall be only used for debugging purposes. It is
|
|
strongly recommended to keep this settings at default value
|
|
to ensure compliance with specification.
|
|
value: 0
|
|
BLE_PHY_DBG_TIME_TXRXEN_READY_PIN:
|
|
description: >
|
|
When set to proper GPIO pin number, this pin will be set
|
|
to high state when radio is enabled using PPI channels
|
|
20 or 21 and back to low state on radio EVENTS_READY.
|
|
This can be used to measure radio ram-up time.
|
|
value: -1
|
|
|
|
BLE_PHY_DBG_TIME_ADDRESS_END_PIN:
|
|
description: >
|
|
When set to proper GPIO pin number, this pin will be set
|
|
to high state on radio EVENTS_ADDRESS and back to low state
|
|
on radio EVENTS_END.
|
|
This can be used to measure radio pipeline delays.
|
|
value: -1
|
|
|
|
BLE_PHY_DBG_TIME_WFR_PIN:
|
|
description: >
|
|
When set to proper GPIO pin number, this pin will be set
|
|
to high state on radio EVENTS_RXREADY and back to low
|
|
state when wfr timer expires.
|
|
This can be used to check if wfr is calculated properly.
|
|
value: -1
|
|
|
|
BLE_PHY_NRF52840_ERRATA_164:
|
|
description: >
|
|
Enable workaround for anomaly 164 found in nRF52840.
|
|
"[164] RADIO: Low selectivity in long range mode"
|
|
This shall be only enabled for:
|
|
- nRF52840 Engineering A
|
|
value: 0
|
|
|
|
BLE_PHY_NRF52840_ERRATA_191:
|
|
description: >
|
|
Enable workaround for anomaly 191 found in nRF52840.
|
|
"[191] RADIO: High packet error rate in BLE Long Range mode"
|
|
This shall be only enabled for:
|
|
- nRF52840 Engineering B
|
|
- nRF52840 Engineering C
|
|
- nRF52840 Rev 1 (final silicon)
|
|
value: 1
|
|
|