We have a lot of infrastructure to delay local channel_updates to
avoid spamming on each peer reconnect; we had to keep tracking of
pending ones though, in case we needed the very latest for sending an
error when failing an HTLC.
Instead, it's far simpler to set the local_disabled flag on a channel
when we disconnect, but only send a disabling channel_update if we
actually fail an HTLC.
Note: handle_channel_update() TAKES update (due to tal_arr_dup), but we
didn't use that before. Now we do, add annotation.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Manipulate fees via fake-bitcoin-cli. It's not quite the same, as
these are pre-smoothing, so we need a restart to override that where
we really need an exact change. Or we can wait until it reaches a
certain value in cases we don't care about exact amounts.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We don't respond to fee changes until we're locked in: make sure we catch
up at that point.
Note that we use NORMAL fees during opening, but IMMEDIATE after, so
this often sends a fee update. The tests which break, we set those
feerates to be equal.
This (sometimes) changes the behavior of test_permfail, as we now
get an immediate commit, so that is fixed too so we always wait for
that to complete.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
When in this state, we send a canned error "Awaiting unilateral close".
We enter this both when we drop to chain, and when we're trying to get
them to drop to chain due to option_data_loss_protect.
As this state (unlike channel errors) is saved to the database, it means
we will *never* talk to a peer again in this state, so they can't
confuse us.
Since we set this state in channel_fail_permanent() (which is the only
place we call drop_to_chain for a unilateral close), we don't need to
save to the db: channel_set_state() does that for us.
This state change has a subtle effect: we return WIRE_UNKNOWN_NEXT_PEER
instead of WIRE_TEMPORARY_CHANNEL_FAILURE as soon as we get a failure
with a peer. To provoke a temporary failure in test_pay_disconnect we
take the node offline.
Reported-by: Christian Decker @cdecker
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Prior to this, lightningd would hand uninteresting peers back to connectd,
which would then return it to lightningd if it sent a non-gossip msg,
or if lightningd asked it to release the peer.
Now connectd hands the peer to lightningd once we've done the init
handshake, which hands it off to openingd.
This is a deep structural change, so we do the minimum here and cleanup
in the following patches.
Lightningd:
1. Remove peer_nongossip handling from connect_control and peer_control.
2. Remove list of outstanding fundchannel command; it was only needed to
find the race between us asking connectd to release the peer and it
reconnecting.
3. We can no longer tell if the remote end has started trying to fund a
channel (until it has succeeded): it's very transitory anyway so not
worth fixing.
4. We now always have a struct peer, and allocate an uncommitted_channel
for it, though it may never be used if neither end funds a channel.
5. We start funding on messages for openingd: we can get a funder_reply
or a fundee, or an error in response to our request to fund a channel.
so we handle all of them.
6. A new peer_start_openingd() is called after connectd hands us a peer.
7. json_fund_channel just looks through local peers; there are none
hidden in connectd any more.
8. We sometimes start a new openingd just to send an error message.
Openingd:
1. We always have information we need to accept them funding a channel (in
the init message).
2. We have to listen for three fds: peer, gossip and master, so we opencode
the poll.
3. We have an explicit message to start trying to fund a channel.
4. We can be told to send a message in our init message.
Testing:
1. We don't handle some things gracefully yet, so two tests are disabled.
2. 'hand_back_peer .*: now local again' from connectd is no longer a message,
openingd says 'Handed peer, entering loop' once its managing it.
3. peer['state'] used to be set to 'GOSSIPING' (otherwise this field doesn't
exist; 'state' is now per-channel. It doesn't exist at all now.
4. Some tests now need to turn on IO logging in openingd, not connectd.
5. There's a gap between connecting on one node and having connectd on
the peer hand over the connection to openingd. Our tests sometimes
checked getpeers() on the peer, and didn't see anything, so line_graph
needed updating.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Rusty Russell
Christian Decker